Brand Name: Happymodel
Item Name: Mobula7 1S 75mm Micro FPV whoop drone
Wheelbase: 75mm
Size: 99mm*99mm*40mm
Weight: 24g
Motor
— Mode: RS0802 KV20000
— Configu-ration:9N12P
— Stator Diamter:8mm
— Stator Length:2mm
— Shaft Diameter:Φ1.5mm
— Motor Dimension(Dia.*Len):Φ10.5mm*13.5mm
— Weight(g):2.0g
— No.of Cells(Lipo):1S only
Propellers
— Weight:0.24g
— Material:PC
— Pitch:1 inch
— Props Dia:40mm
— Center Thickness:5mm
— Center Hole Dia:1.5mm
Flight controller
— X12 ELRS V1.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
— MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
— Sensor: MPU6000 or ICM20689(SPI connection)
— Mount hole size: 25.5mm*25.5mm
— Power supply: 1S battery input (DC 2.9V-4.35V)
— Built-in 12A(each) Blheli_S 4in1 ESC
— Built-in Betaflight OSD(SPI Control)
— Built-in 5.8G OpenVTX 0mw~400mw
— Built-in ExpressLRS 2.4G,Frsky D8/D16,Flysky AFHDS 2A
— Built-in voltage detection
— Built-in current sensor
Onboard 4in1 ESC
— Power supply: 1S LiPo/LiPo HV
— Current: 12A continuous peak 15A (3 seconds)
— Support BLHeliSuite programmable
— Factory firmware: Z_H_30_REV16_7.HEX
— Default protocol: DSHOT300
— Support Bluejay firmware
Onboard SPI ExpressLRS 2.4GHz Receiver
— Packet Rate option: 50Hz/150Hz/250Hz/500Hz
— ExpressLRS Firmware version: V2.0
— RF Frequency: 2.4GHz
— Antenna : SMD antenna
— Telemetry output Power: <12dBm
— Receiver protocol:  SPI ExpressLRS
— Compatible with ExpressLRS V2.0 TX Module
— Couldn’t flash separately ExpressLRS firmware
Onboard 5.8g OPENVTX
— Firmware version: OPENVTX
— Smartaudio v2.1
— PIT Mode support
— RCE Mode support
— Channels:48ch
— Transmitting Power: 0/RCE/25mw/100mw/400mw
— Power supply: DC 5V
— Current (5v): <650ma (400mw)
Runcam Nano3
— Model: RunCam Nano 3
— Image Sensor: 1/3″ CMOS
— Horizontal Resolution: 800TVL
— Lens: 2.1mm(M8) FOV 150°
— Signal System: NTSC
— S/N Ratio: >50dB
— Electronic Shutter Speed: Auto
— Auto Gain Control (AGC): Auto
— Min. Illumination: 0.01Lux@1.2F
— D-WDR: Auto
— Day/Night: Color
— Power:DC 3-5.5V
— Current: 110mA@5V  120mA@3.3V
— Housing Material: ABS
— Net Weight: 1.2g
— Dimensions: L14mm*W14mm*H9mm
Lipo Battery(Not include)
— Capacity:650mAh
— Voltage:3.8v
— Continuous Discharge Rate: 30C
— Instantaneous discharge rate: 60C
— Size: 60mmx18mmx8mm
— Weight: 16g
— Connector: PH2.0